Cabletron Systems 9C106 Guia de Instalação

9032031-01 SmartSwitch 9500 9A656-04 ATM ModuleHardware and Installation Guide

Introduction1-2 Overview The 9A656-04 (shown in Figure 1-1) is a 4.5 Gbps, single slot module for the SmartSwitch 9500 chassis. Up to four ATM Networ

1-3Overview Figure 1-1. The 9A656-04ANANANAN2031_01

Introduction1-4 Features The features of the 9A656-04 are described in the sections below: Processor The 9A656-04 is equipped with an advanced Intel

1-5Related Manuals LANVIEW LEDs The 9A656-04 uses LANVIEW, The Cabletron Systems built-in visual diagnostic and status monitoring system. With LANVIE

Introduction1-6 Getting Help For additional support related to this device or document, contact the Cabletron Systems Global Call Center:Before calli

2-1 Chapter 2 Installing the 9A656-04 Module SmartSwitch 9500 modules can be installed in any of the slots that are available. To install a module, p

Installing the 9A656-04 Module2-2 Figure 2-1. Installing the 9A656-042031_02ANANANANCircuit CardCard GuidesMetal Back-PanelPlastic Locking TabPlastic

2-3The Reset Switch The Reset Switch The Reset switch is located on the front panel, under the top plastic tab as shown in Figure 2-2. It serves two

Installing the 9A656-04 Module2-4 The Module Card DIP Switch An eight position DIP switch is located on the module card as shown in Figure 2-3. The f

2-5Installing an ANIM Installing an ANIM Figure 2-3 shows the location of the 4 motherboard connectors, and the 16 standoff screws for the ATM Networ

Installing the 9A656-04 Module2-6 The 9A656-04 module is shipped without ANIMs. To install the ANIMs proceed as follows:1. Remove the module if it is

2-7Installing an ANIM 5. Press straight down Þrmly on the ANIM until the pins slide all the way into the motherboard connector. Ensure that the ANIM

Installing the 9A656-04 Module2-8

3-1 Chapter 3 Operation The 9A656-04 provides switching between the front panel interfaces (ANIMs) and the Cell Transfer Matrix backplane located ins

Operation3-2ATM Cell Traffic Flow in the 9A656-04The 9A656-04 SmartSwitch utilizes several innovative features that result in a completely redundant, f

3-3ATM Cell Traffic Flow in the 9A656-04CTM (Cell Transfer Matrix) ASICsThe 9A656-04 has seven CTM ASICs that provide two interfaces each between the T

Operation3-4System Management BusesThere are two management channels within the SmartSwitch 9500 system: ¥ SMB-1¥ SMB-10 These buses provide out-of-ba

3-5System Diagnostic ControllerSystem Diagnostic ControllerThis diagnostic controller is composed of a Z-80 microprocessor and its supporting logic. T

Operation3-6

4-1 Chapter 4 LANVIEW LEDs The front panel LANVIEW LEDs indicate the status of the module and may be used as an aid in troubleshooting. Shown in Figu

iNotice Notice Cabletron Systems reserves the right to make changes in speciÞcations and other information contained in this document without prior n

LANVIEW LEDs4-2 Table 4-1. SMB and CPU LEDs LED LED Color State DeÞnition SMBGreen Functional Fully operationalAmber CrippledNot fully operational (i

4-3 ANIM LEDs The front panel LANVIEW LEDs indicate the status of the ANIM and may be used as an aid in troubleshooting. Shown in Figure 4-2 are the

LANVIEW LEDs4-4

5-1Chapter 5General SpecificationsThe speciÞcations for the 9A656-04 are detailed in the sections that follow.Operating SpecificationsEnvironmental Requ

General Specifications5-2PhysicalDimensions35.0 D x 44.0 H x 3.0 W centimeters(13.8 D x 17.4 H x 1.2 W inches)WeightUnit: 1.36 kg. (3lb)Shipping: 1.81

5-3ANIM SpecificationsANIM-21/3The ANIM-21/3 provides a multimode Þber connection using a Duplex SC connector and a line rate of 155.52 Mbps. The speci

General Specifications5-4ANIM-29/3The ANIM-29/3 provides a single mode Þber connection using a Duplex SC connector with a line rate of 155.52 Mbps. The

5-5ANIM SpecificationsANIM-29/3LRThe ANIM-29/3LR provides a single mode Þber connection using a Duplex SC connector with a line rate of 155.52 Mbps. Th

General Specifications5-6ANIM-31/2The ANIM-31/2 provides a multimode Þber connection using a Duplex SC connector with a line rate of 622 Mbps. The spec

5-7ANIM SpecificationsANIM-39/2The ANIM-39/2 provides a single mode Þber connection using a Duplex SC connector with a line rate of 622 Mbps. The speci

Noticeii FCC Notice This device complies with Part 15 of the FCC rules. Operation is subject to the following two conditions: (1) this device may not

General Specifications5-8ANIM-39/2LRThe ANIM-39/2LR provides a single mode Þber connection using a Duplex SC connector with a line rate of 622 Mbps. Th

5-9ANIM SpecificationsANIM-67/2The ANIM-67/2 provides a coaxial cable connection using BNC connectors with a line rate of 45 Mbps. The speciÞcations fo

General Specifications5-10ANIM-77/2The ANIM-77/2 provides a coaxial cable connection using BNC connectors with a line rate of 34 Mbps. The speciÞcation

5-11ANIM SpecificationsANIM-22/4The ANIM-22/3 provides a Category 5 UTP connection using four RJ45 connectors with a line rate of 155.52 Mbps. The spec

General Specifications5-12

iiiNotice Declaration of Conformity Application of Council Directive(s): 89/336/EEC73/23/EEC ManufacturerÕs Name: Cabletron Systems, Inc. Manufacture

Noticeiv

v Contents Chapter 1 Introduction Document Objectives...

Contentsvi Chapter 4 LANVIEW LEDs ANIM LEDs .......

1-1 Chapter 1 Introduction Document Objectives This document, the SmartSwitch 9500 9A656-04 ATM Module Hardware and Installation Guide , contains in