Cabletron Systems 2000 Guia do Utilizador

2M46-04R/2M46-04RDCSmartSwitch 2000User’s Guide2314 00COMRESET2M46-04R21HSIM 1HSIM 2PWRCPU 9032363-02

CONTENTSviii 2M46-04R/2M46-04RDC User’s Guide CHAPTER 4 TROUBLESHOOTING 4.1 Using LANVIEW...

Chapter 5: Local Management5-52 2M46-04R/2M46-04RDC User’s Guide5.15.3 Image File Download Using RuntimeTo download a new firmware image into FLASH usi

Port Redirect Function Screen2M46-04R/2M46-04RDC User’s Guide 5-535.16 PORT REDIRECT FUNCTION SCREENThe Port Redirect Function screen, Figure 5-21, al

Chapter 5: Local Management5-54 2M46-04R/2M46-04RDC User’s GuideThe following definitions briefly explain each field of the Port Redirect Function screen

Port Redirect Function Screen2M46-04R/2M46-04RDC User’s Guide 5-555.16.2 Changing Source and Destination PortsAdd or delete source port and destinatio

Chapter 5: Local Management5-56 2M46-04R/2M46-04RDC User’s Guide5.17 BROADCAST SUPPRESSION SCREENThe Broadcast Suppression screen, Figure 5-22, allows

Broadcast Suppression Screen2M46-04R/2M46-04RDC User’s Guide 5-57The following explains each field of the Broadcast Suppression screen:Port # (Read-onl

Chapter 5: Local Management5-58 2M46-04R/2M46-04RDC User’s Guide5.17.2 Setting the Reset Peak RateTo reset the Peak Rate field to zero, proceed as foll

Device Statistics Menu Screen2M46-04R/2M46-04RDC User’s Guide 5-59Figure 5-23 Device Statistics Menu ScreenThe Device Statistics Menu screen displays

Chapter 5: Local Management5-60 2M46-04R/2M46-04RDC User’s Guide5.19 SWITCH STATISTICS SCREENThe Switch Statistics screen, Figure 5-24, lists the numb

Switch Statistics Screen2M46-04R/2M46-04RDC User’s Guide 5-61Frames Txmtd (Read-Only)Displays the number of frames transmitted by the interface since

CONTENTS2M46-04R/2M46-04RDC User’s Guide ix 5.11 Device Specific Configuration Menu Screen ... 5-375.12 System Resources Sc

Chapter 5: Local Management5-62 2M46-04R/2M46-04RDC User’s Guide5.20 INTERFACE STATISTICS SCREENThe Interface Statistics screen, Figure 5-25, is used

Interface Statistics Screen2M46-04R/2M46-04RDC User’s Guide 5-63The following definitions explain each field of the Interface Statistics screen:Interfac

Chapter 5: Local Management5-64 2M46-04R/2M46-04RDC User’s GuideOutOctets (Read-only)This field displays the total number of octets (bytes) that have b

Interface Statistics Screen2M46-04R/2M46-04RDC User’s Guide 5-65MTU (Read-only)The maximum transmission unit (MTU) field displays the maximum data field

Chapter 5: Local Management5-66 2M46-04R/2M46-04RDC User’s Guide5.20.2 Using the Clear Counters CommandTo reset all the statistics counters of the sel

RMON Statistics Screen2M46-04R/2M46-04RDC User’s Guide 5-67The following definitions explain each field of the RMON Statistics screen:RMON Index (Read-o

Chapter 5: Local Management5-68 2M46-04R/2M46-04RDC User’s GuideMulticast Pkts (Read-only)The Multicast Pkts field displays the total number of good fr

RMON Statistics Screen2M46-04R/2M46-04RDC User’s Guide 5-69Total Octets (Read-only)This field displays the total number of octets (bytes) of data, incl

Chapter 5: Local Management5-70 2M46-04R/2M46-04RDC User’s Guide5.21.1 Displaying RMON StatisticsTo display the statistics for any index, proceed as f

Network Tools2M46-04R/2M46-04RDC User’s Guide 5-71Figure 5-27 Network Tools ScreenThe Network Tools functions are performed using a series of commands

CONTENTSx 2M46-04R/2M46-04RDC User’s Guide APPENDIX B FE-100TX, FE-100FX, AND FE-100F3 SPECIFICATIONS B.1 FE-100TX...

Chapter 5: Local Management5-72 2M46-04R/2M46-04RDC User’s GuideThe commands are presented in the following format:command:Syntax: Shows the required

Network Tools2M46-04R/2M46-04RDC User’s Guide 5-73Each ARP cache entry lists the network interface that the device is connected to, the device’s netwo

Chapter 5: Local Management5-74 2M46-04R/2M46-04RDC User’s Guidebridge:Syntax: bridge [enable/disable] [ifnum/all]Description: The bridge command allo

Network Tools2M46-04R/2M46-04RDC User’s Guide 5-75netstat:Syntax: netstat [option]Description: The netstat command provides a display of general netwo

Chapter 5: Local Management5-76 2M46-04R/2M46-04RDC User’s Guidereset:Syntax: resetDescription: This reset command initiates a hardware reset of the d

Network Tools2M46-04R/2M46-04RDC User’s Guide 5-77Example:traceroute:Syntax: traceroute [IP address]Description: The traceroute command generates a TR

Chapter 5: Local Management5-78 2M46-04R/2M46-04RDC User’s Guidesoft-reset:Syntax: soft-resetDescription: This command restarts the software image, wh

Network Tools2M46-04R/2M46-04RDC User’s Guide 5-79Example:link_trap:Syntax: link_trap [enable/disable/status][PORT/all]Description: The link_trap comm

Chapter 5: Local Management5-80 2M46-04R/2M46-04RDC User’s Guideatm_stp_state:Syntax: atm_stp_state [STATE]Description: The atm_stp_state command allo

2M46-04R/2M46-04RDC User’s Guide A-1APPENDIX ASPECIFICATIONSThis appendix provides operating specifications for the Cabletron Systems 2M46-04R and 2M46

2M46-04R/2M46-04RDC User’s Guide 1-1 CHAPTER 1INTRODUCTION Welcome to the 2M46-04R/04RDC SmartSwitch 2000 User’s Guide . This guide describes the

Appendix A: SpecificationsA-2 2M46-04R/2M46-04RDC User’s GuideA.4 ENVIRONMENTAL REQUIREMENTSA.5 INPUT/OUTPUT PORTSTable A-2 2M46-04RDCLine Input Range

COM Port/Pin Assignments2M46-04R/2M46-04RDC User’s Guide A-3A.6 COM PORT/PIN ASSIGNMENTSThe COM port is a serial communications port that supports Loc

Appendix A: SpecificationsA-4 2M46-04R/2M46-04RDC User’s Guide

2M46-04R/2M46-04RDC User’s Guide B-1APPENDIX BFE-100TX, FE-100FX, AND FE-100F3 SPECIFICATIONSThe 2M46-04R supports three Fast Ethernet Interface Modul

Appendix B: FE-100TX, FE-100FX, and FE-100F3 SpecificationsB-2 2M46-04R/2M46-04RDC User’s GuideB.2 FE-100FXThe FE-100FX shown in Figure B-2 uses an SC

FE-100F32M46-04R/2M46-04RDC User’s Guide B-3B.3 FE-100F3The FE-100F3 shown in Figure B-3 uses an SC style connector that supports single mode fiber opt

Appendix B: FE-100TX, FE-100FX, and FE-100F3 SpecificationsB-4 2M46-04R/2M46-04RDC User’s Guide

2M46-04R/2M46-04RDC User’s Guide C-1APPENDIX COPTIONAL INSTALLATIONS AND MODE SWITCH BANK SETTINGSThe top cover must be removed to gain access to the

Appendix C: Optional Installations and Mode Switch Bank SettingsC-2 2M46-04R/2M46-04RDC User’s GuideC.2 REMOVING THE CHASSIS COVERThis section describ

Removing the Chassis Cover2M46-04R/2M46-04RDC User’s Guide C-3Figure C-1 Removing the Chassis CoverC.2.1 Setting the Mode SwitchFigure C-2 shows the l

Chapter 1: Introduction 1-2 2M46-04R/2M46-04RDC User’s Guide Appendix A, Specifications , contains information on functionality and operating specifi

Appendix C: Optional Installations and Mode Switch Bank SettingsC-4 2M46-04R/2M46-04RDC User’s GuideFigure C-2 2M46-04R Mode Switch Location/Component

Removing the Chassis Cover2M46-04R/2M46-04RDC User’s Guide C-5• Switch 7 – Clear NVRAM. Changing the position of this switch resets NVRAM on either th

Appendix C: Optional Installations and Mode Switch Bank SettingsC-6 2M46-04R/2M46-04RDC User’s GuideC.3 INSTALLING OPTIONAL FAST ETHERNET INTERFACE MO

Installing Optional Fast Ethernet Interface Modules2M46-04R/2M46-04RDC User’s Guide C-7To install a Fast Ethernet Interface Module in port slot 1 or 2

Appendix C: Optional Installations and Mode Switch Bank SettingsC-8 2M46-04R/2M46-04RDC User’s GuideFigure C-4 Coverplate Removal2. Remove the screw f

Installing Optional Fast Ethernet Interface Modules2M46-04R/2M46-04RDC User’s Guide C-9Figure C-5 Installing the Fast Ethernet Interface Module5. Pres

Appendix C: Optional Installations and Mode Switch Bank SettingsC-10 2M46-04R/2M46-04RDC User’s Guide

2M46-04R/2M46-04RDC User’s Guide Index-1INDEXNumerics100BASE-FXcable length 2-22M46-04Roverview of 1-2AAccess policy 5-30BBridge Configuration screens

IndexIndex-2 2M46-04R/2M46-04RDC User’s GuideHHelp 1-9related manuals 1-10High Speed Configuration Interface screen 5-44High Speed Interface Configura

Index2M46-04R/2M46-04RDC User’s Guide Index-3defroute 5-74link_trap 5-75netstat 5-75ping 5-75reset 5-76show 5-76soft-reset 5-77telnet 5-77traceroute 5

2M46-04R Overview2M46-04R/2M46-04RDC User’s Guide 1-3 The 2M46-04R is a tabletop unit that can be installed in a standard 19-inch rack using the supp

IndexIndex-4 2M46-04R/2M46-04RDC User’s GuideNetwork Tools screen 5-70Password screen 5-8Port Redirect Function screen 5-53RMON Statistics screen 5-66

Chapter 1: Introduction 1-4 2M46-04R/2M46-04RDC User’s Guide 1.3.3 Auto-Negotiation The optional FE-100TX Fast Ethernet Interface Module can auto-ne

2M46-04R Overview2M46-04R/2M46-04RDC User’s Guide 1-5 1.3.5 Runtime IP Address Discovery This feature enables the 2M46-04R to automatically accept an

Chapter 1: Introduction 1-6 2M46-04R/2M46-04RDC User’s Guide 1.3.7 Switching The 2M46-04R provides traditional switching (802.1D), IEEE 802.1Q switc

2M46-04R Overview2M46-04R/2M46-04RDC User’s Guide 1-7 1.3.11 Optional Features Options for the 2M46-04R include Fast Ethernet Interface Modules and H

Chapter 1: Introduction 1-8 2M46-04R/2M46-04RDC User’s Guide 1.4 DOCUMENT CONVENTIONS The following conventions are used throughout this document:NO

Getting Help2M46-04R/2M46-04RDC User’s Guide 1-9 1.5 GETTING HELP For additional support related to this device or document, contact the Cabletron Sy

Chapter 1: Introduction1-10 2M46-04R/2M46-04RDC User’s Guide1.6 RELATED MANUALSThe following manuals may help to set up, control, and manage the 2M46-

2M46-04R/2M46-04RDC User’s Guide 2-1CHAPTER 2NETWORK REQUIREMENTSBefore installing the 2M46-04R or Fast Ethernet Interface Module, review the requirem

Chapter 2: Network Requirements2-2 2M46-04R/2M46-04RDC User’s Guide2.3 100BASE-FX FIBER OPTIC NETWORKPorts 1 and 2 of the 2M46-04R support the Cabletr

2M46-04R/2M46-04RDC User’s Guide 3-1CHAPTER 3INSTALLATIONThis chapter provides all instructions required to install the 2M46-04R. A Phillips screwdriv

Chapter 3: Installation3-2 2M46-04R/2M46-04RDC User’s Guide3.2 INSTALLING OPTIONSIf the 2M46-04R is to be installed with an optional Fast Ethernet Int

Installing the 2M46-04R2M46-04R/2M46-04RDC User’s Guide 3-3Locate the 2M46-04R on an unrestricted free surface area as shown in Figure 3-1. Proceed to

Chapter 3: Installation3-4 2M46-04R/2M46-04RDC User’s Guide3.3.2 2M46-04R and 2M46-04RDC Rackmount InstallationGuidelines for the Rackmount Installati

Installing the 2M46-04R2M46-04R/2M46-04RDC User’s Guide 3-5Figure 3-2 Attaching the Strain-Relief BracketThere are two methods for attaching the rackm

2M46-04R/2M46-04RDC User’s Guide i NOTICE Cabletron Systems reserves the right to make changes in specifications and other information contained in th

Chapter 3: Installation3-6 2M46-04R/2M46-04RDC User’s GuideFigure 3-3 Installing the Rackmount Brackets3. With the mounting brackets installed, positi

Installing the 2M46-04R2M46-04R/2M46-04RDC User’s Guide 3-74. Locate the four 6-32 x 3/8-inch flathead cover replacement screws in the rackmount kit.

Chapter 3: Installation3-8 2M46-04R/2M46-04RDC User’s Guide3.4 CONNECTING POWERThe 2M46-04R connects to an ac power source and the 2M46-04RDC connects

Connecting Power2M46-04R/2M46-04RDC User’s Guide 3-92. Observe the LANVIEW LEDs. After a successful boot, the CPU LED turns ON (green). If the PWR LED

Chapter 3: Installation3-10 2M46-04R/2M46-04RDC User’s GuideTo connect the 2M46-04RDC to a 48/60 Vdc power source, face the back of the device, then r

Connecting to the Network2M46-04R/2M46-04RDC User’s Guide 3-113.5 CONNECTING TO THE NETWORKThis section provides the procedures for connecting UTP and

Chapter 3: Installation3-12 2M46-04R/2M46-04RDC User’s GuideFigure 3-9 FE-100TX Crossover SwitchA schematic of a crossover cable is shown in Figure 3-

Connecting to the Network2M46-04R/2M46-04RDC User’s Guide 3-13b. Verify that the RJ45 connector on the twisted pair segment has the proper pinouts.c.

Chapter 3: Installation3-14 2M46-04R/2M46-04RDC User’s Guide2. Insert one end of the SC connector into the FE-100FX or FE-100F3 installed in the 2M46-

Completing the Installation2M46-04R/2M46-04RDC User’s Guide 3-154. Verify that a link exists by checking that the port RX LED is ON (flashing amber, b

Noticeii 2M46-04R/2M46-04RDC User’s Guide INDUSTRY CANADA NOTICE This digital apparatus does not exceed the Class A limits for radio noise emissions

Chapter 3: Installation3-16 2M46-04R/2M46-04RDC User’s Guide

2M46-04R/2M46-04RDC User’s Guide 4-1CHAPTER 4TROUBLESHOOTINGThis chapter provides information concerning the following:• Using the LANVIEW diagnostic

Chapter 4: Troubleshooting4-2 2M46-04R/2M46-04RDC User’s GuideNOTEThe terms flashing, blinking, and solid used in the following tables indicate the fo

Using LANVIEW2M46-04R/2M46-04RDC User’s Guide 4-3RX(Receive)Off No link. No activity. Port enabled or disabled.None.Green Solid. Port enabled, link, n

Chapter 4: Troubleshooting4-4 2M46-04R/2M46-04RDC User’s Guide4.2 FE-100TX LEDThe optional FE-100TX has one LED labeled 10/100. The 10/100 LED togethe

FE-100TX LED2M46-04R/2M46-04RDC User’s Guide 4-5Table 4-3 10/100 LED Indications When RX LED Is OffNOTENo link exists if the associated port (1 or 2)

Chapter 4: Troubleshooting4-6 2M46-04R/2M46-04RDC User’s Guide4.3 TROUBLESHOOTING CHECKLISTIf the 2M46-04R is not working properly, refer to Table 4-4

Using the RESET Button2M46-04R/2M46-04RDC User’s Guide 4-74.4 USING THE RESET BUTTONThe RESET button shown in Figure 4-3 resets the 2M46-04R processor

Chapter 4: Troubleshooting4-8 2M46-04R/2M46-04RDC User’s Guide

2M46-04R/2M46-04RDC User’s Guide 5-1CHAPTER 5LOCAL MANAGEMENTThis chapter explains how to set up a management terminal to access Local Management. It

Notice2M46-04R/2M46-04RDC User’s Guide iii CABLETRON SOFTWARE PROGRAM LICENSE 1. LICENSE. You have the right to use only the one (1) copy of the Prog

Chapter 5: Local Management5-2 2M46-04R/2M46-04RDC User’s Guide5.2 LOCAL MANAGEMENT KEYBOARD CONVENTIONSAll key names appear as capital letters in thi

Management Terminal Setup2M46-04R/2M46-04RDC User’s Guide 5-35.3 MANAGEMENT TERMINAL SETUPUse one of the following systems to access Local Management:

Chapter 5: Local Management5-4 2M46-04R/2M46-04RDC User’s GuideFigure 5-1 Management Terminal ConnectionRJ45 COM PortRJ45-to-DB9PC AdapterUTP Cablewit

Management Terminal Setup2M46-04R/2M46-04RDC User’s Guide 5-55.3.2 Management Terminal Setup ParametersTable 5-2 lists the setup parameters for the lo

Chapter 5: Local Management5-6 2M46-04R/2M46-04RDC User’s Guide5.3.3 Telnet ConnectionsOnce the 2M46-04R has a valid IP address, a Telnet session with

Management Terminal Setup2M46-04R/2M46-04RDC User’s Guide 5-7Figure 5-2 Uninterruptible Power Supply (UPS) ConnectionRJ45 COM PortRJ45-to-DB9UPS Adapt

Chapter 5: Local Management5-8 2M46-04R/2M46-04RDC User’s Guide5.4 ACCESSING LOCAL MANAGEMENTAccess to Local Management is controlled through the Pass

Accessing Local Management2M46-04R/2M46-04RDC User’s Guide 5-9• If an invalid password is entered, the terminal beeps and the cursor returns to the be

Chapter 5: Local Management5-10 2M46-04R/2M46-04RDC User’s Guide\Figure 5-4 802.1D Switching Mode, LM Screen Hierarchy\Figure 5-5 802.1Q Switching Mod

Accessing Local Management2M46-04R/2M46-04RDC User’s Guide 5-11\Figure 5-6 SecureFast VLAN Mode, LM Screen Hierarchy5.4.2 Selecting Local Management M

Noticeiv 2M46-04R/2M46-04RDC User’s Guide SAFETY INFORMATIONCLASS 1 LASER TRANSCEIVERSTHE FE-100F3 FAST ETHERNET INTERFACE MODULE, FPIM-05 AND FPIM-0

Chapter 5: Local Management5-12 2M46-04R/2M46-04RDC User’s Guide3. Exit from 2M46-04R Local Management by repeating steps 1 and 2 until the Device Men

Device Menu Screen2M46-04R/2M46-04RDC User’s Guide 5-13The following explains each Device Menu screen field as shown in Figure 5-7:DEVICE CONFIGURATION

Chapter 5: Local Management5-14 2M46-04R/2M46-04RDC User’s Guide5.6 DEVICE CONFIGURATION MENU SCREENThe Device Configuration Menu screen, Figure 5-8, p

Device Configuration Menu Screen2M46-04R/2M46-04RDC User’s Guide 5-15The following briefly explains each screen accessible from the Device Configuration

Chapter 5: Local Management5-16 2M46-04R/2M46-04RDC User’s Guide5.7 GENERAL CONFIGURATION SCREENThe General Configuration screen, Figure 5-9, allows th

General Configuration Screen2M46-04R/2M46-04RDC User’s Guide 5-17Subnet Mask (Modifiable)Displays the subnet mask for the 2M46-04R. A subnet mask “masks

Chapter 5: Local Management5-18 2M46-04R/2M46-04RDC User’s GuideDevice Uptime (Read-Only)Displays the total time that the device has been operating.Op

General Configuration Screen2M46-04R/2M46-04RDC User’s Guide 5-19Clear NVRAM (Toggle)This allows the user to reset NVRAM to the factory default setting

Chapter 5: Local Management5-20 2M46-04R/2M46-04RDC User’s GuideFigure 5-10 Configuration Warning Screen5. Use the arrow keys to highlight the YES comm

General Configuration Screen2M46-04R/2M46-04RDC User’s Guide 5-214. Use the arrow keys to highlight the SAVE command, then press ENTER. The warning scr

Notice2M46-04R/2M46-04RDC User’s Guide v DECLARATION OF CONFORMITY Application of Council Directive(s): 89/336/EEC73/23/EEC Manufacturer’s Name: Cabl

Chapter 5: Local Management5-22 2M46-04R/2M46-04RDC User’s Guide3. Press ENTER. If the TFTP gateway IP address entered is a valid format, the cursor r

General Configuration Screen2M46-04R/2M46-04RDC User’s Guide 5-235.7.6 Setting the Device TimeTo set the device time, perform the following steps:1. Us

Chapter 5: Local Management5-24 2M46-04R/2M46-04RDC User’s Guide5.7.8 Setting the Screen Lockout TimeThe screen lockout time can be set from 1 to 30 m

General Configuration Screen2M46-04R/2M46-04RDC User’s Guide 5-255.7.10 Configuring the COM PortUpon power up, the COM port is configured to the default

Chapter 5: Local Management5-26 2M46-04R/2M46-04RDC User’s GuideFigure 5-11 COM Port Warning Screen3. Use the arrow keys to highlight YES. Press ENTER

General Configuration Screen2M46-04R/2M46-04RDC User’s Guide 5-272. Use the SPACE bar or BACKSPACE to step through the available settings until the ope

Chapter 5: Local Management5-28 2M46-04R/2M46-04RDC User’s Guide5.7.11 Clearing NVRAMClearing NVRAM allows the user to clear all user-entered paramete

SNMP Community Names Screen2M46-04R/2M46-04RDC User’s Guide 5-295.7.12 Enabling/Disabling IP Fragmentation To enable or disable IP fragmentation, proc

Chapter 5: Local Management5-30 2M46-04R/2M46-04RDC User’s GuideFigure 5-13 SNMP Community Names ScreenThe following explains each SNMP Community Name

SNMP Community Names Screen2M46-04R/2M46-04RDC User’s Guide 5-31super-user This community name gives the user read-write access to the 2M46-04R MIB ob

Noticevi 2M46-04R/2M46-04RDC User’s Guide

Chapter 5: Local Management5-32 2M46-04R/2M46-04RDC User’s Guide5.9 SNMP TRAPS SCREENSince the 2M46-04R is an SNMP compliant device, it can send messa

SNMP Traps Screen2M46-04R/2M46-04RDC User’s Guide 5-335.9.1 Configuring the Trap TableTo configure the Trap table, proceed as follows:1. Use the arrow k

Chapter 5: Local Management5-34 2M46-04R/2M46-04RDC User’s Guide5.10 SWITCH CONFIGURATION SCREENThe Switch Configuration screen, Figure 5-15, provides

Switch Configuration Screen2M46-04R/2M46-04RDC User’s Guide 5-35The following describes each field of the Switch Configuration screen:Switch Address (Rea

Chapter 5: Local Management5-36 2M46-04R/2M46-04RDC User’s GuideStatus (Toggle)Allows the user to disable or enable a port by setting the status of th

Device Specific Configuration Menu Screen2M46-04R/2M46-04RDC User’s Guide 5-375.10.3 Setting (Enabling or Disabling) the Port StatusTo set the status of

Chapter 5: Local Management5-38 2M46-04R/2M46-04RDC User’s GuideFigure 5-16 Device Specific Configuration Menu ScreenThe following explains each selecta

System Resources Screen2M46-04R/2M46-04RDC User’s Guide 5-39PORT REDIRECT FUNCTIONThe Port Redirect Function screen allows the user to redirect traffic

Chapter 5: Local Management5-40 2M46-04R/2M46-04RDC User’s GuideFigure 5-17 System Resources Screen The following briefly explains each field of the Sys

System Resources Screen2M46-04R/2M46-04RDC User’s Guide 5-41Peak Switch Utilization (Read-only)Shows the peak percentage of maximum switching capacity

2M46-04R/2M46-04RDC User’s Guide vii CONTENTS CHAPTER 1 INTRODUCTION 1.1 Using This Guide...

Chapter 5: Local Management5-42 2M46-04R/2M46-04RDC User’s Guide5.13 HIGH SPEED INTERFACE CONFIGURATION MENU SCREENTo access the High Speed Interface

High Speed Interface Configuration Menu Screen2M46-04R/2M46-04RDC User’s Guide 5-43The following briefly explains each screen accessible from the High S

Chapter 5: Local Management5-44 2M46-04R/2M46-04RDC User’s Guide5.14 HIGH SPEED INTERFACE CONFIGURATION SCREENThe High Speed Interface Configuration sc

High Speed Interface Configuration Screen2M46-04R/2M46-04RDC User’s Guide 5-45The following briefly explains each field of the High Speed Interface Config

Chapter 5: Local Management5-46 2M46-04R/2M46-04RDC User’s GuideIf an FE-100TX is installed, the field steps to Auto-Negotiation, 10Base-T, 10Base-TFD

High Speed Interface Configuration Screen2M46-04R/2M46-04RDC User’s Guide 5-475.14.2 Setting the FE-100FX or FE-100F3Desired Operational ModeUse this fi

Chapter 5: Local Management5-48 2M46-04R/2M46-04RDC User’s Guide5.14.5 Setting the FE-100TX Advertised Ability In normal operation, a port (1 or 2) wi

Flash Download Screen2M46-04R/2M46-04RDC User’s Guide 5-49To access the Flash Download screen from the Device Specific Configuration Menu screen, use th

Chapter 5: Local Management5-50 2M46-04R/2M46-04RDC User’s GuideReboot After Download (Modifiable when RUNTIME is chosen only)This field notifies the use

Flash Download Screen2M46-04R/2M46-04RDC User’s Guide 5-514. Set the IP address of the TFTP gateway server (this defaults to the same IP address set i