Cabletron Systems SmartSwitch Router Guia do Utilizador

90333806H203-24 and 6H253-13SmartSwitch 6000 Interface ModulesInstallation User’s Guide

viii If the Program is exported from the United States pursuant to the License Exception TSR under the U.S. Export Administration Regulations, in addi

ixDECLARATION OF CONFORMITYApplication of Council Directive(s): 89/336/EEC73/23/EECManufacturer’s Name: Cabletron Systems, Inc.Manufacturer’s Address:

x

xiContentsFigures... xiiiTabl

xii2NETWORK REQUIREMENTS2.1 SmartTrunk... 2-12.2 10

xiiiFiguresFigure Page1-1 The 6H203-24 and 6H253-13 SmartSwitches...1-23-1 Installing an

xivTablesTable Page3-1 Contents of Shipping Container ... 3-14-1 LANVI

xvAbout This GuideWelcome to the Cabletron Systems 6H203-24 and 6H253-13 SmartSwitch 6000 Interface Modules Installation User’s Guide. This guide desc

Structure of This GuidexviSTRUCTURE OF THIS GUIDEThis guide is organized as follows:This section provides preliminary information that will aid in usi

Related ManualsxviiRELATED MANUALSThe following manuals are recommended to help the user to set up and manage the SmartSwitches:• SmartSwitch Series 6

Document ConventionsxviiiDOCUMENT CONVENTIONSThe following conventions are used throughout this document:NOTENote symbol. Calls the reader’s attention

Introduction 1-11IntroductionThis chapter introduces the 6H203-24 and 6H253-13 SmartSwitch 6000 interface modules and provides information about how t

Overview1-2 IntroductionFigure 1-1 The 6H203-24 and 6H253-13 SmartSwitches SystemLEDCOM PortNetworkPorts 1-12VHSIM/HSIMSlotPort StatusLEDsPort StatusL

OverviewIntroduction 1-31.1.1 ConnectivityThe SmartSwitch modules connect to Ethernet networks or workstations through the RJ21 ports on the front pan

Overview1-4 IntroductionWhen the modules are connected to the network and powered up, Runtime IP Address Discovery (RAD) checks the modules for an IP

OverviewIntroduction 1-51.1.6 Remote Monitoring (RMON)The SmartSwitches support all nine Ethernet RMON groups. The Statistics, Alarms, Events and Hist

Overview1-6 IntroductionAdministrators can configure up to four rate limit rules per port; however, each rule must not include conflicting 802.1p prio

OverviewIntroduction 1-7Frame based 802.3x flow control is supported on all Ethernet ports operating in the full duplex mode. Flow control can be enab

Overview1-8 Introduction1.1.15 Distributed Chassis ManagementFrom a management perspective, the 6C105 SmartSwitch 6000 chassis can be viewed as a sing

Getting HelpIntroduction 1-91.2 GETTING HELPFor additional support related to this device or document, contact Cabletron Systems using one of the foll

iNOTICECabletron Systems reserves the right to make changes in specifications and other information contained in this document without prior notice. T

Network Requirements 2-12Network RequirementsBefore installing the SmartSwitch modules, review the requirements and specifications referred to in this

100BASE-TX Network2-2 Network Requirements2.3 100BASE-TX NETWORKThe fixed ports of the SmartSwitch provide an RJ21 connection that supports Category 5

Installation 3-13InstallationThis chapter covers the following items:• Unpacking the Module (Section 3.1)• Installing Options (Section 3.2)• Installin

Installing Options3-2 Installation3.2 INSTALLING OPTIONSIf installing an optional HSIM or VHSIM, it must be installed in the 6H253-13 before proceedin

Installing the Module into the 6C105 ChassisInstallation 3-3Figure 3-1 Installing an Interface Module5. Examine the module for damage. If any damage e

Connecting to the Network3-4 Installation6. Locate the slot guides that line up with the number of the slot in which the module will be installed. Ins

Connecting to the NetworkInstallation 3-5.Figure 3-2 Connecting a Twisted Pair Segment to the SmartSwitch3. Verify that a link exists by checking that

Completing the Installation3-6 Installatione. Ensure that the twisted pair connection meets the dB loss and cable specifications outlined in the Cable

Troubleshooting 4-14TroubleshootingThis chapter provides information concerning the following:• Using the LANVIEW diagnostic and status monitoring sys

iiFCC NOTICEThis device complies with Part 15 of the FCC rules. Operation is subject to the following two conditions: (1) this device may not cause ha

Using LANVIEW4-2 TroubleshootingTable 4-1 provides the definitions of the LED states that occur when the LED mode switch is in the UP position. Table

Using LANVIEWTroubleshooting 4-3Figure 4-1 LANVIEW LEDsCPU LED121413COMCPU34567891011 1215 166H252-17Fast Enet2X4X6X8X10X12X14X16XDPXSPDRXTXLED Mode S

Using LANVIEW4-4 TroubleshootingTable 4-1 LANVIEW LEDs CPU, Receive, and Transmit StatusLED Color State Recommended ActionCPU Off Power off. Power up

Using LANVIEWTroubleshooting 4-5Table 4-2 Speed and Full Duplex LED IndicationsTX Off Port enabled, and no activity. Should flash green every two seco

Troubleshooting Checklist4-6 Troubleshooting4.2 TROUBLESHOOTING CHECKLISTIf the 6H203-24 or 6H253-13 are not working properly, refer to Table 4-3 for

Troubleshooting ChecklistTroubleshooting 4-7Table 4-4 Power System TroubleshootingPossible Causes InstructionLoss of Power to the 6C105 chassis.Perfor

Troubleshooting Checklist4-8 TroubleshootingTable 4-5 Firmware TroubleshootingPossible Causes InstructionAutobaud enabled. Press ENTER (RETURN) (may t

Troubleshooting ChecklistTroubleshooting 4-9Table 4-6 Management System TroubleshootingPossible Causes InstructionImproper Community Names Table.1. Re

Troubleshooting Checklist4-10 TroubleshootingTable 4-7 Device Setup TroubleshootingPossible Causes InstructionThe module detects a looped condition.1.

Using the RESET ButtonTroubleshooting 4-114.3 USING THE RESET BUTTONThe RESET button located near the upper plastic locking tab of the module (refer t

iiiCABLETRON SYSTEMS, INC.PROGRAM LICENSE AGREEMENTIMPORTANT:THIS LICENSE APPLIES FOR USE OF PRODUCT IN THE FOLLOWING GEOGRAPHICAL REGIONS:CANADAMEXIC

Specifications A-1ASpecificationsThis appendix provides operating specifications for the Cabletron Systems SmartSwitch Interface Modules. Cabletron Sy

Input/Output PortsA-2 SpecificationsA.4 INPUT/OUTPUT PORTS6H253-13 Specifications6H203-24 SpecificationsA.5 COM PORT PINOUT ASSIGNMENTSThe COM port is

Regulatory ComplianceSpecifications A-3A.6 REGULATORY COMPLIANCEThis equipment meets the following safety and electromagnetic compatibility (EMC) requ

Switch Settings, Upgrades, and Installations B-1BSwitch Settings, Upgrades, and InstallationsThis appendix covers the following items:• Setting the mo

Setting the Mode SwitchesB-2 Switch Settings, Upgrades, and InstallationsFigure B-1 Module Mode Switch Location/Component LayoutSwitch definitions and

SIMM UpgradeSwitch Settings, Upgrades, and Installations B-3• Switch 8 – Reset Password/Community Strings. Changing the position of this switch clears

SIMM UpgradeB-4 Switch Settings, Upgrades, and InstallationsB.2.2 Installing the DRAM SIMMTo install a DRAM SIMM, refer to Figure B-3 and proceed as f

Installing Optional High Speed Interface ModulesSwitch Settings, Upgrades, and Installations B-5B.3 INSTALLING OPTIONAL HIGH SPEED INTERFACE MODULESFi

ivIf the Program is exported from the United States pursuant to the License Exception TSR under the U.S. Export Administration Regulations, in additio

Index-1IndexNumerics100BASE-TX requirements 2-210BASE-Tconnection 3-4requirements 2-1AAuto-Negotiation 1-3CCable specifications100BASE-TX network 2-21

Index-2RRedirect functionsport and VLAN, introduction to 1-5Regulatory Compliance A-3Related Manuals xviiRESET button 4-11Runtime IP Address Discovery

vCABLETRON SYSTEMS SALES AND SERVICE, INC.PROGRAM LICENSE AGREEMENTIMPORTANT: THIS LICENSE APPLIES FOR USE OF PRODUCT IN THE UNITED STATES OF AMERICA

vi5. UNITED STATES GOVERNMENT RESTRICTED RIGHTS. The enclosed Product (i) was developed solely at private expense; (ii) contains “restricted computer

viiCABLETRON SYSTEMS LIMITEDPROGRAM LICENSE AGREEMENTIMPORTANT: THIS LICENSE APPLIES FOR THE USE OF THE PRODUCT IN THE FOLLOWING GEOGRAPHICAL REGIONS: